Canon error Code

Canon error messages shown below:

E000Fuser problem, Fuser heater, Fuser film, Thermistor, Connections, Power Supply
E001Fuser Temperature too high, Fuser heater, Fuser film, Thermistor, Connections, Power Supply  
E002E003Low Fuser Temperature, Thermistor, Fuser heater, Fuser film, Connections, Power Supply
E004Fuser problem, triac shorted, thermistor, power supply
E007Fuser film rotation problem ( IR 2200, 2800, 3300 or i )
E009Fuser does not match power supply or DC controller board 
E010Drive problem, main motor, motor drive board, mechanical gear functions 
E014-0000Fuser motor ( IR 2200, 2800, 3300 or i )
E019-0000Waste toner full ( IR 2200, 2800, 3300 or i )
E032-0001DA unit communications error ( IR 2200, 2800, 3300 or i )
E040Holding plate drive assembly, holding plate position sensor or holding plate solenoid
E043Paper deck feed motor problem
E051-0000Horizontal registration home detect mechanism ( Motor M9 or sensor PS10 ) ( IR 2200, 2800, 3300 or i )
E054Duplex feed roller home position sensor lever, duplex feed roller gear, duplex drive board, duplex feed clutch, or duplex motor
E055Horizontal registration guide, home sensor lever, drive gear, duplex drive board, horizontal registration motor or duplex drive motor
E064-0000

Charge, transfer or developer bias problem

E100Laser unit, BD mirror, image processor board, laser board, DC controller, can also happen if drum is not installed
E102Laser problem 
E110-0000Laser motor ( IR 2200, 2800, 3300 or i )
E202-0001Scan problem, scan switch, scan motor, image processor board ( IR 2200, 2800, 3300 or i ), panel locked with error message
E203Scan motor driver board, scan motor or reader controller board 
E204-0001ADF lead edge image signal problem ( IR 2200, 2800, 3300 or i )
E211/215Reader controller board, exposure lamp heater, exposure lamp thermistor, flat cable connections
E216Exposure lamp, inverter board, reader controller board
E217Exposure lamp heater or heater controller board
E219Exposure lamp, inverter board, reader controller board
E220-00001Exposure lamp inverter board ( IR 2200, 2800, 3300 or i )
E225-0000,-00002White plate/edge whit plate read error, bad CCD or exposure lamp ( IR 2200, 2800, 3300 or i )
E240-0000Mcon-Dcon problem, bad DC controller ( IR 2200, 2800, 3300 or i )
E243-0000Control panel to image processor board communication problem, main controller board ( IR 2200, 2800, 3300 or i )
E248-0001EEPROM problem ( IR 2200, 2800, 3300 or i )
E261-0000Zero cross signal problem, main control board or DC controller board
E302-0001, -0002Shading error, CCD, reader board or main controller board ( IR 2200, 2800, 3300 or i ) 

E315

Image data problem, main controller board ( IR 2200, 2800, 3300 or i )
E400RDF to copier communication problem
E401RDF pickup motor or pickup sensor
E402RDF belt motor or pulse sensor
E403RDF feed motor or pulse sensor
E404DRF delivery motor problem
E420-0001ADF back up data ( IR 2200, 2800, 3300 or i )
E421-0001ADF back up data ( IR 2200, 2800, 3300 or i ), communication problem
E422-0001ADF IPC error
E500Finisher main board or communication with copier
E501-0001 Saddle finisher communications with punch
E503-03Finisher saddle-stitcher communication problem
E504-01,-02,-03,-04Finisher height sensor problem
E505-0001,-0002Finisher back up RAM error
E510-0001,-0002Finisher feed motor ( IR 2200, 2800, 3300 or i )
E512-01,-02Finisher delivery motor or delivery motor clock sensor
E513-01,-02Finisher alignment motor or alignment motor home sensor 
E514Stack delivery motor, sensor
E530

Rear jogging plate motor, sensor

E531
Finisher stapler motor, home sensor 
E532-01,-02Finisher stapler motor or its home sensor
E535-01,-02Finisher delivery motor or its swing guide switches
E535-03Finisher safety switch or swing guide switch
E537Front jogging plate motor M3, front aligning plate home sensor 
E540-0000,-00002,-0003Finisher tray up/down motor ( IR 2200, 2800, 3300 or i ) E551Finisher fan
E577Finisher delivery motor or sensor
E580Finisher stack tray upper limit sensor or up/down motor problem
E583Finisher tray aux plate motor or sensor
E584-01,-02,-03Finisher feed motor, feed motor switch or shutter closed switch
E585-0000Finisher stack handling
E590-0000,-0002Punch motor
E592-0000,-0002,-0003,-0004,-0005Horizontal registration sensor, 0006 is punch sensor error
E593-0001,-0003 Punch shift motor
E5F1-0001,-0002,-0003Finisher saddle folder motor
E601-0000,-0001Image transfer error, hard drive, main controller, DC controller
E602-0001,-0002Hard disk error, reinstalled software, hard drive or DC controller bad
E604-0000

Image memory, hard drive or main controller board

E605-0001
Image memory battery, hard drive or main controller board 
E606-0001HDD mounting fault, reinstalled software, replace HDD or main controller board, connections
E674-0000Fax unit problem
E676 PDL board connection, PDL board, systems controller board
E677-0001PDL board, printer board or main controller board
E710-0001,-0002,-0003IPC initialization problem 
E711-0001,-0002,-0003IPC register
E712-0001,-0002Communication problem with document feeder
E713-0000Communication problem with finisher
E716-0000Communication problem with pedestal
E717-0001Communication problem with ASSIST
E719-0001Card reader, coin vendor communication problem 
E731Relay board, PDA board, network board, image processor board, system controller board
E732-0001Reader communication problem
E733-0001Printer communication problem 
E734Relay board, PDA board, network board, image processor board, system controller board
E735Relay board, PDA board, network board, image processor board, system controller board
E736Fax board or system controller board

E737-0000SDRAM problem, DIMM or system controller
E738Network board, relay board, system controller board
E739Network board, relay board, system controller board
E740-0001,-0002,-0003Ethernet board
E741-0000PCI bus error
E742RIPI board 
E743-0000Mcon-Rcon communication error
E744-0000Boot ROM software problem
E803-0000Low voltage power supply problem 
E804Printer unit power supply fan, DC controller
E805
Laser motor, DC controller, ( Developer Fan or other Fan on IR series ), Bad fan, DC controller or image processor board
E807Fuser /scanner fan or DC controller
E810(IR models) No drum in machine
E826Bypass fan or DC controller board
E827Controller power supply fan problem
E901-0000Pedestal feed unit motor or board   
E903

Paper deck lift problem 

Sharp copiers error code messages

Sharp copiers error code messages

Sharp-AR series copier error messages: *_*Auditor not ready 
C1v      Sub code 00: Charge corona problem
C2v      Sub code 00: Transfer corona problem
CEApplies to *7* models v      Sub code 00: Communication problem with network cablev      Sub code 01: Communication error with print server cardv      Sub code 02: Mail server or FTP not foundv      Sub code 03: Server does not correspond during image transmissionv      Sub code 04: Entered account number of FTP server or password not goodv      Sub code 05: FTP server entered directory is not good EEv      Sub code EL: Problem during developer calibration, over tonedv      Sub code EU: Problem during developer calibration, under toned
E7v      Sub code 00: ICU-PCU communication problemv      Sub code 01: Image data memory problemv      Sub code 02: Laser problemv      Sub code 03: Hard drive problemv      Sub code 10: Black correction shading problem from CCDv      Sub code 11: White correction shading problem from CCDv      Sub code 13: Exposure lamp light amount adjustment incorrectv      Sub code 90: ICU-PCU communication problem
FAv      Sub code 01: A2 board problem (Memory)
FCv      Sub code 00: ASK/lrDA modulation LSI reset errorv      Sub code 01: ASK/lrDA switch error
F1v      Sub code 00: Communication error between main board and finisherv      Sub code 01: Finisher jogger shift problemv      Sub code 02: Finisher transport drivev      Sub code 04: Finisher index lower limit problemv      Sub code 05: Finisher index upper limit problemv      Sub code 06: Finisher shift problemv      Sub code 08: Finisher stapler shift motor problemv      Sub code 10: Stapler problemv      Sub code 11: Pusher motor problemv      Sub code 14: Stack tray problemv      Sub code 15: Finisher elevator motor problemv      Sub code 16: Staple sorter holding motorv      Sub code 17: ST pressure release home position problemv      Sub code 18: Tray 3 exit paddle problemv      Sub code 50: Non-support trouble in option connectionv      Sub code 80: Finisher power problem
F2v      Sub code 00: Toner sensorv      Sub code 02: Toner motor disconnectedv      Sub code 31: Process control problem, drum or sensor not working properlyv      Sub code 32: Drum mark sensor problem, drum or sensorv      Sub code 37: Drum mark sensor gain adjustment problemv      Sub code 39: Processor unit thermistor (Not Fuser)
F3v      Sub code 12: Upper cassette lift problemv      Sub code 22: Lower cassette lift problem
F9v      Sub code 00: ICU-PRT problemv      Sub code 01: PRT DRAM problemv      Sub code 03: Network card problemv      Sub code 04: Printer program errorv      Sub code 10: PRT SCSI LSI problemv      Sub code 90: ICU-PRT problem 
Note: In codes E7, F9, U0 the following sub codes all have the same meanings:Sub code 82, 83, 84, 85, 86, 8L, 87, 88, 89, 8H, 8C, 8U, 8F, 90, 91 Communication error between main board and sub board, operation board, ICU board or PRT
H2v      Sub code 00 & 01: Fuser thermistor open 
H3v      Sub code 00 & 01: Fuser temperature too high
H4v      Sub code 00 & 01: Fuser temperature to low, check fuser assemblyH5v      Sub code 01: Exit sensor problemv      Sub code 02: Fuser thermistor problem
L1v      Sub code 00: Scan forward problem, motor, sensor, board
L3v      Sub code 00: Scan return problem, motor, sensor, board
L4v      Sub code 01: Drive problem, main motor, gear, sensor, bind
v      Sub code 02: Drum Drive Problem
v      Sub code 03: Fuser Fan Problem
v      Sub code 04: Developer Motor
v      Sub code 06: Transfer Belt Separator Motor
v      Sub code 30: Controller Fan
v      Sub code 31: Paper Exit Fan Problem
L6v      Sub code 10: Laser problem, motor, sensor, board
L8v      Sub code 01: No full wave signal (PCU)v      Sub code 02: Full wave signal problem (PCU)

PCPersonal counter missing
PFv      Sub code 00: RIC copy inhibition signal received from host computer
U2v      Sub code 00: EEPROM read/write problemv      Sub code 11: Counter check sum errorv      Sub code 12: Adjust value check sum error
U4v      Sub code 02: Duplex alignment plate out of position, motor, cable, sensorv      Sub code 03: Duplex rear plate problem
U5v      Sub code 00: Communication problem between main board and document feederv      Sub code 01: Document feeder resist sensor problemv      Sub code 02: Document feeder invert / eject sensorv      Sub code 03: Document feeder timing sensorv      Sub code 06: Document feeder post separation sensor problemv      Sub code 07: Document feeder read sensor problemv      Sub code 08: Document feeder SB sensor problemv      Sub code 11: Document feeder paper feed drive problemv      Sub code 16: Document feeder fan problem
U6v      Sub code 00: Desk communication problemv      Sub code 01-03: Desk lift problemv      Sub code 08: Desk 24 volt power supplyv      Sub code 09: LCT lift motor problemv      Sub code 10: Desk transport errorv      Sub code 20: LCT communication problemv      Sub code 22: LCT 24 volt problemv      Sub code 50: Non support trouble in auto detect of deskv      Sub code 51: Non support trouble in auto detect of LCT
U7v      Sub code 00: RIC communication problem (ICU board)
U9v      Sub code 00: Communication problem (ICU detect)v      Sub code 90: Communication problem; ICU-OPE
Sharp AR-M350 / 450 series also applies to Imagistics IM3510 IM4510
C1v      Sub code 00: Charge corona problem
CEv      Sub code 00: Miscellaneous e-mail related errorv      Sub code 01: Network interface card problemv      Sub code 02: FTP error or can’t find mail serverv      Sub code 03: Server down during scanv      Sub code 04: Invalid account name or password for FTP server enteredv      Sub code 05: Invalid FTP server directory enteredCHDoor openv      Sub code 00: Developer cartridge unit missingv      Sub code 01: Toner cartridge missing EEv      Sub code EL: Problem during developer calibration over tonedv      Sub code EU: Problem during developer calibration under toned
E6v      Sub code 10: CIS problem (Black correction) v      Sub code 11: CIS problem (White correction)v      Sub code 14: CIS-ASIC communication problem
E7v      Sub code 02: Laser problemv      Sub code 03: Hard drive problemv      Sub code 06: Control board decode problemv      Sub code 10: Shading problem (Black correction)v      Sub code 11: Shading problem (White correction)v      Sub code 14: CCD-ASIC communication problemv      Sub code 50: Laser connectionv      Sub code 80: Scan board communication problemv      Sub code 90: PCU communication problem
F1v      Sub code 00: Communication error with finisher or mail bin stackerv      Sub code 02: Mail box stacker drive motor problemv      Sub code 03: Console finisher paddle motorv      Sub code 06: Console finisher slide motorv      Sub code 08: Finisher stapler shift motor problemv      Sub code 10: Finisher or console finisher stapler problemv      Sub code 11: Finisher or console finisher bundle motor problemv      Sub code 12: Mail box gatev      Sub code 15: Finisher or console finisher lift motor problemv      Sub code 19: Finisher or console finisher front alignment motor problemv      Sub code 20: Finisher or console finisher aligning motor problemv      Sub code 30: Console finisher communication problem v      Sub code 31: Console finisher fold problem, sensorv      Sub code 32: Console finisher punch communication problemv      Sub code 33: Console finisher side punch motor registerv      Sub code 34: Console finisher punch motorv      Sub code 35: Console finisher side punch motor register sensorv      Sub code 36: Console finisher punch timer sensorv      Sub code 37: Console finisher RAMv      Sub code 38: Console finisher punch RAMv      Sub code 80: Finisher or mail box 24 volt problemv      Sub code 81: Console finisher transport motorv      Sub code 87: Finisher stapler rotate motor
F2v      Sub code 00: Toner sensorv      Sub code 02: Toner problemv      Sub code 04: Wrong cartridge, destination or life cyclev      Sub code 05: CRUM problemSub code 39: Process unit thermistor (Not Fuser)

F3v      Sub code 12: Tray 1 lift problemv      Sub code 22: Multi purpose lift problem
F6v      Sub code 00: Fax communication problemv      Sub code 01: Fax flash ROM problemv      Sub code 04: Fax modem problem
F7v      Sub code 01: Fax board EEPROM read/write error
F9v      Sub code 02: Centro port error (Control Board)v      Sub code 03: Network card problem (Control Board)H2v      Sub code 00: Fuser thermistor for HL1 openv      Sub code 01: Fuser thermistor for HL2 open
H3v      Sub code 00: HL1 fuser temperature too highv      Sub code 01: HL2 fuser temperature too high
H4v      Sub code 00: HL1 fuser temperature too low, troubleshoot!v      Sub code 01: HL2 fuser temperature too low, fuser assembly
H5v      Sub code 01: Exit sensor problem
L1v      Sub code 00: Scan forward problem
L3v      Sub code 00: Scan return problem
L4v      Sub code 01: Drive problem, main motor, gear, sensor, bindv      Sub code 02: Drum drive motor problem
L6v      Sub code 10: Laser problem, motor, sensor, board
L8v      Sub code 01: No full wave signal problem (PCU)v      Sub code 02: Full wave signal problem (PCU)
PCPersonal counter missing PFRIC copy inhibition signal received from host computer. Hint Reset 17  
U1v      Sub code 01: Fax board battery problemv      Sub code 02: RTC read problem (Fax or ICU board)
U2v      Sub code 00: EEPROM read/write problemv      Sub code 11: Control board EEPROM adjust value check sum errorv      Sub code 12: Control board EEPROM adjust value check sum errorv      Sub code 80: Scanner EEPROMv      Sub code 81: Scanner memory check sum errorv      Sub code 90: PCU EEPROM read/write problemv      Sub code 91: PCU memory check sum problemv      Hint reset 16 U6v      Sub code 00: Desk or LCT communication problemv      Sub code 01-03: Desk or LCC multi-purpose tray lift problemsv      Sub code 10: Desk or LCC transport motor
U7v      Sub code 00: MODEM –PC problem

Sharp Color Machines MX-Series Maintenance Codes

AA maintenance counters for both black/white and color reaches 90% of set value
CA color copies/prints maintenance counter reaches 90% of set value
TA maintenance counter total reaches 90% of set value 

TK2 the secondary transfer unit print counter reaches 300,000 sheets

FUSER UNIT COUNTERS
FK1 the fusing upper and lower heat roller print counter reaches 300,000 sheets

FK2 the fusing sub heat roller print counter reaches 150,000 sheets

FK3 the fusing web print counter reaches 150,000 sheets 

IMAGING DRUM CARTRIDGES SYSTEM COUNTERS
DK imaging drum cartridge black counter reaches 150,000 or the accumulated number of rotations of the drum black reaches 840k
DC imaging drum cartridge cyan counter reaches 100,000 or the accumulated number of rotations of the drum cyan reaches 840k
DM imaging drum cartridge magenta counter reaches 100,000 or the accumulated number of rotations of the drum magenta reaches 840k
DY imaging drum cartridge yellow counter reaches 100,000 or the accumulated number of rotations of the drum yellow reaches 840k

DEVELOPER CARTRIDGE SYSTEM COUNTERSVK developer print counter black reaches 150,000 sheets or the accumulated number of rotations of the developer black reaches 840k
VC developer print counter cyan reaches 100,000 sheets or the accumulated number of rotations of the developer cyan reaches 840k
VM developer print counter magenta reaches 100,000 sheets or the accumulated number of rotations of the developer magenta reaches 840k
VY developer print counter yellow reaches 100,000 sheets or the accumulated number of rotations of the developer yellow reaches 840k