How To Fix Error Code on the Printer Canon MP287

How To Fix Error Code on the Printer Canon MP287 :

If you Get Error Code on your Printer Canon MP287, Please Do not panic, just reading this article and try intruction on this article. To find the easiest solution before you bring your printer to the service , it helps us try to understand first some code error on the Canon MP287 printer and also the solution .
Not much different from previous series , the Canon MP287 also has two types namely Error code :1 . who use the first letter P , for example P022 . who use the first letter E , for example E03As for some Canon MP287 Error code of the most common are:E 1.

Code Error on Canon Printer MP287 :

Error Code E02
Cause : Ran out of paper printer ( printer is out of paper ) or paper does not go well .
Solution : Load paper correctly .

Error Code E03
Cause : Paper Jams ( Jammed Paper ) or Paper Output Closed . Opening Paper Output ,
Solution : Reload the paper correctly .

Error Code E04 or E05
Cause : Cartridge not detected / not terkenali by the printer ( The FINE Cartridge can not be recognized ) . Cartridges must be installed properly or not Compatible .
Solution : Try to Remove the Cartridge first , then plug it back by pushing the keys until the cartridge clicks into place .

Error Code E07
Cause : Cartridge is not installed in the correct position ( the FINE Cartridge is not installed in the correct position) .
Solution : Check if Cartridge Black / Color already in the correct position .

Error Code E08
Penybab : Ink absorber is almost full ( Ink absorber is almost full ) .
Solution : Press the Black or Color button on your printer to Resume Printing ( Continue Printing ) .

Error Code E13
Cause : The remaining ink can not be detected ( The Remaining ink level can not be detected) .
Solution : Replace Ink Cartridges with new and original . If you want to continue without replacing new cartridge , press the STOP / RESET on your Printer For 5 seconds .

Error Code E14
Cause : Cartridge not recognized ( The FINE Cartridge can not be recognized ) .
Solution : Replace the old cartridge with a new cartridge .

Error Code E15
Cause : Cartridge not recognized ( The FINE Cartridge can not be recognized ) . Cartridge is not installed correctly .
Solution : Try Remove the cartridge then plug it back into place until you click the Cartridge lock .

Error Code E16
Cause : The ink has Run Out .
Solution : If the printer is printing the data , press the STOP / RESET for 5 seconds then continue your printing . Replace Ink Cartridges kosong.E30 : The document is too small when ” Fit Copying is Selected” , check the position of the document on the scanner glass .

Error Code E31
Cause : The printer is not connected to the computer ( the printer is not connected with the computer ) .
Solution : Connect the USB cable from the printer to the USB port on the computer .

Error Code E50
Cause : Scanning the print head alignment sheet has failed .
Solution : Press the STOP / RESET . Make sure the paper is loaded ( A4 or other size ) in accordance with the print head alignment , and also the paper in the correct position and not a dirty glass plate . Also make sure the Print Head Nozzles are not clogged .

Error code P At Canon printer MP287 :

Error Code P02
Solution : Cancel printing and turn off your printer . Clean up / pull papers pertaining to your printer . Maybe you Cartridge Damaged / Broken . Turn your printer back .

Error Code P10
Turn off your printer and then turn it back on .
Other error cases are also common :
Turn off your printer and unplug the AC power cord and then plug it back into your printer 

Download Resetter Canon MP287 Error P07

Download Resetter Canon MP287 Error P07– When you will print using the Canon MP287 printer and display experience becomes number 1 and then changed again into the letter “P” and then widened the letter “0” then becomes “7”, and keeps getting repeated and power button lights flashing “BLINK”

Thus, the printer has a problem with informing us that the error code “P07”, when it was forced to print it will appear the windows on your computer screen, P07 shows Error Code Counter printing solution is already full and we had to reset it. Steps we will take to overcome the problem is to make the printer in Service mode MODE / SAVE MODE, then we use the Counter Reset Software.

Do the following:
1. Log SAVE MODE printer:

• The printer is off, the power cord is not disconnected from the electricity;
• Press the STOP / RESET and hold;
• Press the Power button, so that the button is still depressed;
• Release the button STOP / RESET;
• POWER button is pressed, push the button STOP / RESET much as 6x, each time you push, warning lights will be flashing, the printer responds to pressure you;
• If successful, the printer will carry out Rollernya, the current display will BLANK, at the time of your desktop will respond “no new device” ignore it.

2. Reset the Software:

• Download software Reset below
• Extract the downloaded file
• Run the EXE file it, and will appear as pic below:
  
• Click the EEPROM (1) to see the LOG / printer records, provide one sheet of paper.
• Click the SET button (2) to reset the ink counter.
• Click SET (3) to reset Absorted Ink
• Then the printer OFF.
• MP287 printer is ready to be reused

Download Resetter Canon MP287 Error P07

Download Resetter Canon MP287 Error P07

Download Resetter Canon MP287 Error P07– When you will print using the Canon MP287 printer and display experience becomes number 1 and then changed again into the letter “P” and then widened the letter “0” then becomes “7”, and keeps getting repeated and power button lights flashing “BLINK”

Thus, the printer has a problem with informing us that the error code “P07”, when it was forced to print it will appear the windows on your computer screen, P07 shows Error Code Counter printing solution is already full and we had to reset it. Steps we will take to overcome the problem is to make the printer in Service mode MODE / SAVE MODE, then we use the Counter Reset Software.

Do the following:
1. Log SAVE MODE printer:

• The printer is off, the power cord is not disconnected from the electricity;
• Press the STOP / RESET and hold;
• Press the Power button, so that the button is still depressed;
• Release the button STOP / RESET;
• POWER button is pressed, push the button STOP / RESET much as 6x, each time you push, warning lights will be flashing, the printer responds to pressure you;
• If successful, the printer will carry out Rollernya, the current display will BLANK, at the time of your desktop will respond “no new device” ignore it.

2. Reset the Software:

• Download software Reset below
• Extract the downloaded file
• Run the EXE file it, and will appear as pic below:
  
• Click the EEPROM (1) to see the LOG / printer records, provide one sheet of paper.
• Click the SET button (2) to reset the ink counter.
• Click SET (3) to reset Absorted Ink
• Then the printer OFF.
• MP287 printer is ready to be reused

Download Resetter Canon MP287 Error P07

Toshiba Copiers Error Code Messages

Toshiba Copiers Error Code Messages  

Toshiba E-studio 16, 20, 25 are equivalent to Xerox Pro 416 and 421.If machine has picture of wrench a code is present to read code press down “8” and “clear/stop” key simultaneously. All codes, except fuser error codes are reset by turning machine off and back on again. Messages are applicable to Toshiba E Studio 160, 200, DP1600, DP2000, and DP2500 

C01Main motor drive problem
CA2Horizontal sync signal error
C04PFP main drive problem (Tray 3)
C06LCF feed motor
C13Cassette 1
C14Cassette 2
C15Cassette 3
C16Cassette 4
C18LCF tray problem
C19LCF feed motor
C21Scan problem
C25
Scan watchdog error
C26
Exposure lamp
C38Replaced process unit error
C41Fuser thermistor or low temperature
C43Fuser problem after warm-up
C44Fuser problem after warm-upC45Fuser thermistor open
C56Communication error between copier and PFC
C57Communication problem between copier and IPC
C58Communication problem between IPC and finisher
C71Doc feeder paper supply motor problem
C73Doc feeder EEPROM initialization problem
C74Doc feeder exit reverse sensor problem
C81Doc feeder fan
C82Doc feeder aligning sensor
C83Doc feeder size length adjustment error
C91SRAM lithium battery
C95Power supply fan
C96Process unit fan
C97Vacuum fan
C98Clock IC problem
C99PFC microcomputer problem
CA1Laser motor (Polygon motor) problem
CA2Laser HSYNC problem
CB2Finisher exit motorCB5Staple motor
CC3Processing motor
CC8Front aligning motor
CC9Upper tray elevator motor
CCALower tray elevator motor
CCBRear aligning motor
E01Jam
E02Fuser Jam
E03Jam at turn on
E08Duplex jam
E09Paper feed jam
E11Duplex feed jam
E12Bypass jam
E13Upper cassette jam
E142^nd cassette jams (PFU)
E153^rd cassette jam (PFP upper)
E164^th cassette jam (PFP; 20/25)
E19LCF jam (20/25)
E31Cassette 2 jamE32Cassette 3 or 4 jam
E33LCF jam (20/25)
E34Cassette 3 or 4 jam
E36LCF jam (20/25)
E41Front or side door open during copy cycle
E42Cassette 2 or 3 door open during copy cycle
E43Duplex unit open during copy cycle
E45LCF open during copy cycle
E71ADF feed jam
E73ADF exit jam
E74ADF original reverse jam
EA1Finisher transport jam
EA2Finisher jam
EA3Jam at finisher at power on
EA4Finisher door open jam
EA5Stapler jam
EA6Finisher early arrival jam
EA7Finisher transport jam
F11Scanner I/F problemF12Write error downloading scanner problem
F13Download sector error of scanner unit program
F14Scan unit F-ROM error
F21PCON board memory error
F22PC interface board NVRAM error
F31Fax modem IC problem
F41Offset catch tray initial detect error
OF1Intermittent failure
OF2Netware problem
OF3Message without fault code
OF4Network card PCL print error
OF5Network card status not printed
OF6User interface error
OF7Web page print error
OF8Fax problem
OF9Internet fax problem
OF10Stapler
OF11Scan document size sense problem
OF12Offset catch trayOF13Separator tray
OF14Print cartridge (Drum/Dev unit)
OF15Toner detect problem
Toshiba Studio E-28, 35, 45 (DP-2800, 3500, 4500) and some other models are identical troubleshoot with “CS”.
C04Paper feed motor
C13Upper cassette
C14Lower cassette
C15PFP upper cassette
C16PFP lower cassette
C1ALCF end fence motor
C1BLCF motor
C26Peak detect error, exposure lamp
C27, C28Scan home problem
C41Fuser thermistor or low temperature
C43Fuser problem after warm-up or fuser thermistor
C44Fuser problem
C45Side fuser thermistor bad 
C47Power voltage problem
C48High IGBT temperature
C49IH circuit
C55Communication problem between copier and RADF
C57Communication problem between CPU and IPC
C58Communication problem between IPC and finisher
C71ADF feed motor
C73EEPROM initialization problem RADF
C74RADF exit reverse sensor problem
C81RADF fan
C82RADF sensor adjustment error 
C83RADF original sensor adjustment error
C94Main CPU problem
CA1Laser motor (Polygon motor) problem
CA2Laser H-SYNC problem
CA3Laser secondary scan rough adjust error
CA5Laser power adjust error
CA6Laser calibration error
CA9Laser image data transmit error from SYS boardCAALaser secondary fine adjust error
CABLaser secondary scan inter-page error
CACLaser primary scan dot adjust error
CABSecondary scan interpage compensation error
CB1Finisher feed motor
CB2Finisher exit motor
CB3Finisher lift motor
CB4Finisher alignment motor
CB5Staple motor
CB6Stapler shift motor problem
CB7Finisher height sensor
CB8Backup RAM problem
CB9Saddle stitcher paper push plate motor
CBASaddle stitcher front stitcher motor
CBBSaddle stitcher rear stitcher motor
CBCSaddle stitcher alignment motor
CBDSaddle stitcher guide motor
CBESaddle stitcher folding motor
CBFSaddle stitcher paper positioning plate motorCCOFinisher sensor connector error
CC1Finisher micro switch
CC2Saddle stitcher to finisher communication problem
CC3Stack process motor problem
CC4Finisher swing motor
CC5Finisher horizontal registration motor
CC6Finisher punch motor
CC8Front jogger motor
CC9Upper stack tray lift motor
CCALower stack tray lift motor
CCBRear jogger motor
E01Jam before fuser
E02Fuser jam
E03Jam at turn on
E09Hard drive error
E11Duplex jam
E12Bypass jam 

E131^st cassette jam
E142^nd cassette jam 
E153^rd cassette jam 
E164^th cassette jam
E19LCF jam
E20, E21Jams from 1^st cassette
E22Jams from 2^nd cassette
E30, E33PFP upper cassette jam
E34, E36PFP lower cassettes jams
E3C, E3D, E3E, E3FLCF jams
F07Communication error between SYS board and LGC board
F10Hard drive initialization error
F11Communication error between SYS board and SLG board

Toshiba StudioE-550, 650, E-800 equivalent machines Lanier 5555 (Studio E-550), Lanier 5556 and Sharp AR651 (Studio E-650), Lanier 5580 and Sharp AR-810 (Studio E-800)
C04Paper feed motor
C11Duplex side guide
C12Duplex stopper guide problem
C131^st cassette  
C142^nd cassette 
C153^rd cassette   
C164^th cassette
C17PFP lower cassette
C18LCF tray up problem
C1ATandem LCF end fence motor
C1CLCF tray up motor
C26Peak detect error, exposure lamp
C27, C28Scan home problem
C29Exposure lamp problem
C36Charge corona cleaning problem
C37Transfer belt cam motor
CD1Brush motor locked
CD2Toner auger motor locked
CD3Used toner motor
CD4Waste toner full
C41Fuser thermistor or low temperature
C43Fuser problem after warm-up or fuser thermistor
C44Fuser problem
C45Side fuser thermistor bad
C46Fuser pressure roller thermistor badC47Power voltage problem
C48High IGBT temperature
C49IH circuit
C4AFuser web
CD5Web motor path error
C55Communication error between copier and RADF
C56Communication problem between CPU and PFC
C57Communication problem between CPU and IPC
C58Communication problem between IPC and finisher
C59Communication problem between CPU and laser CPU
C72RADF registration sensor problem
C73EEPROM initialization problem in RADF
C74RADF exit reverse sensor problem
C82RADF sensor adjustment error 
C83RADF original sensor adjustment error
C84RADF small original reverse sensor adjustment error
C85RADF lift tray motor
C86RADF large original exit sensor adjustment problem
C94Main CPU problem
CA1Laser motor (Polygon motor) problem
CA2Laser H-SYNC problem
CA3Laser secondary scan rough adjust error
CA5Laser power adjust error
CA6Laser calibration error
CA9Laser image data transmit error from SYS board
CAALaser secondary fine adjust error
CABLaser secondary scan inter-page error
CACLaser primary scan dot adjust error
CABSecondary scan interpage compensation error
CB1Finisher feed motor
CB2Finisher exit motor
CB3Finisher lift motor
CB4Finisher alignment motor
CB5Staple motor
CB6Stapler shift motor problem
CB7Finisher height sensor
CB8Backup RAM problem 
CB9Saddle stitcher paper push plate motor
CBASaddle stitcher front stitcher motor
CBBSaddle stitcher rear stitcher motor
CBCSaddle stitcher alignment motor
CBDSaddle stitcher guide motor
CBESaddle stitcher folding motor
CBFSaddle stitcher paper positioning plate motorCCOFinisher sensor connector error
CC1Finisher micro switch
CC2Saddle stitcher to finisher communication problem
CC4Finisher swing motor
CC5Finisher horizontal registration motor
E11Duplex jam
E12Bypass jam
E131^st cassette jam 
E142^nd cassette jam 
E153^rd cassette jam 
E164^th cassette jam
E18Tandem feed jam
E19LCF jam
E20, E21Jams from 1^st cassette
E22, E24Jams from 2^nd cassette
E25Jams from LCF
E30 - E333^rd cassette jam
E34 - E384^th cassettes jams
CC6Finisher punch motor
CC7Finisher punch unit backup RAM data
CCCFinisher to inserter communication problem
CCDFinisher inserter EEPROM problem
CCEFinisher inserter fan
CDOLaser initialize time out error
CEOLaser comparator problem
CE1Laser beam sensor detect error
CE2Laser sensor busy error
CE3Laser primary scan adjustment error
CE4Laser abnormal window comparator
E01Jam before fuser
E02Fuser jam
E03Jam at turn on
E09Hard drive error
E3C, E3D, E3E, E3FTandem LCF jams
E41 – E47Cover open jam
E50 – E59, E5ADuplex jam
E71 – E77, E7B, E7F, E80 – E85Document feeder jam
EA1 – EA9, E9F, EAA – EB3Finisher jams
EC - EC9, ECA – ECCInserter jam
EB5, EB6Jam in transport area
F07Communication error SYS board and LGC board
F10Hard drive format error
F11Communication error between SYS board and SLG board 

Toshiba Copiers Error Code Messages

Toshiba Copiers Error Code Messages  

Toshiba E-studio 16, 20, 25 are equivalent to Xerox Pro 416 and 421.If machine has picture of wrench a code is present to read code press down “8” and “clear/stop” key simultaneously. All codes, except fuser error codes are reset by turning machine off and back on again. Messages are applicable to Toshiba E Studio 160, 200, DP1600, DP2000, and DP2500 

C01Main motor drive problem
CA2Horizontal sync signal error
C04PFP main drive problem (Tray 3)
C06LCF feed motor
C13Cassette 1
C14Cassette 2
C15Cassette 3
C16Cassette 4
C18LCF tray problem
C19LCF feed motor
C21Scan problem
C25
Scan watchdog error
C26
Exposure lamp
C38Replaced process unit error
C41Fuser thermistor or low temperature
C43Fuser problem after warm-up
C44Fuser problem after warm-upC45Fuser thermistor open
C56Communication error between copier and PFC
C57Communication problem between copier and IPC
C58Communication problem between IPC and finisher
C71Doc feeder paper supply motor problem
C73Doc feeder EEPROM initialization problem
C74Doc feeder exit reverse sensor problem
C81Doc feeder fan
C82Doc feeder aligning sensor
C83Doc feeder size length adjustment error
C91SRAM lithium battery
C95Power supply fan
C96Process unit fan
C97Vacuum fan
C98Clock IC problem
C99PFC microcomputer problem
CA1Laser motor (Polygon motor) problem
CA2Laser HSYNC problem
CB2Finisher exit motorCB5Staple motor
CC3Processing motor
CC8Front aligning motor
CC9Upper tray elevator motor
CCALower tray elevator motor
CCBRear aligning motor
E01Jam
E02Fuser Jam
E03Jam at turn on
E08Duplex jam
E09Paper feed jam
E11Duplex feed jam
E12Bypass jam
E13Upper cassette jam
E142^nd cassette jams (PFU)
E153^rd cassette jam (PFP upper)
E164^th cassette jam (PFP; 20/25)
E19LCF jam (20/25)
E31Cassette 2 jamE32Cassette 3 or 4 jam
E33LCF jam (20/25)
E34Cassette 3 or 4 jam
E36LCF jam (20/25)
E41Front or side door open during copy cycle
E42Cassette 2 or 3 door open during copy cycle
E43Duplex unit open during copy cycle
E45LCF open during copy cycle
E71ADF feed jam
E73ADF exit jam
E74ADF original reverse jam
EA1Finisher transport jam
EA2Finisher jam
EA3Jam at finisher at power on
EA4Finisher door open jam
EA5Stapler jam
EA6Finisher early arrival jam
EA7Finisher transport jam
F11Scanner I/F problemF12Write error downloading scanner problem
F13Download sector error of scanner unit program
F14Scan unit F-ROM error
F21PCON board memory error
F22PC interface board NVRAM error
F31Fax modem IC problem
F41Offset catch tray initial detect error
OF1Intermittent failure
OF2Netware problem
OF3Message without fault code
OF4Network card PCL print error
OF5Network card status not printed
OF6User interface error
OF7Web page print error
OF8Fax problem
OF9Internet fax problem
OF10Stapler
OF11Scan document size sense problem
OF12Offset catch trayOF13Separator tray
OF14Print cartridge (Drum/Dev unit)
OF15Toner detect problem
Toshiba Studio E-28, 35, 45 (DP-2800, 3500, 4500) and some other models are identical troubleshoot with “CS”.
C04Paper feed motor
C13Upper cassette
C14Lower cassette
C15PFP upper cassette
C16PFP lower cassette
C1ALCF end fence motor
C1BLCF motor
C26Peak detect error, exposure lamp
C27, C28Scan home problem
C41Fuser thermistor or low temperature
C43Fuser problem after warm-up or fuser thermistor
C44Fuser problem
C45Side fuser thermistor bad 
C47Power voltage problem
C48High IGBT temperature
C49IH circuit
C55Communication problem between copier and RADF
C57Communication problem between CPU and IPC
C58Communication problem between IPC and finisher
C71ADF feed motor
C73EEPROM initialization problem RADF
C74RADF exit reverse sensor problem
C81RADF fan
C82RADF sensor adjustment error 
C83RADF original sensor adjustment error
C94Main CPU problem
CA1Laser motor (Polygon motor) problem
CA2Laser H-SYNC problem
CA3Laser secondary scan rough adjust error
CA5Laser power adjust error
CA6Laser calibration error
CA9Laser image data transmit error from SYS boardCAALaser secondary fine adjust error
CABLaser secondary scan inter-page error
CACLaser primary scan dot adjust error
CABSecondary scan interpage compensation error
CB1Finisher feed motor
CB2Finisher exit motor
CB3Finisher lift motor
CB4Finisher alignment motor
CB5Staple motor
CB6Stapler shift motor problem
CB7Finisher height sensor
CB8Backup RAM problem
CB9Saddle stitcher paper push plate motor
CBASaddle stitcher front stitcher motor
CBBSaddle stitcher rear stitcher motor
CBCSaddle stitcher alignment motor
CBDSaddle stitcher guide motor
CBESaddle stitcher folding motor
CBFSaddle stitcher paper positioning plate motorCCOFinisher sensor connector error
CC1Finisher micro switch
CC2Saddle stitcher to finisher communication problem
CC3Stack process motor problem
CC4Finisher swing motor
CC5Finisher horizontal registration motor
CC6Finisher punch motor
CC8Front jogger motor
CC9Upper stack tray lift motor
CCALower stack tray lift motor
CCBRear jogger motor
E01Jam before fuser
E02Fuser jam
E03Jam at turn on
E09Hard drive error
E11Duplex jam
E12Bypass jam 

E131^st cassette jam
E142^nd cassette jam 
E153^rd cassette jam 
E164^th cassette jam
E19LCF jam
E20, E21Jams from 1^st cassette
E22Jams from 2^nd cassette
E30, E33PFP upper cassette jam
E34, E36PFP lower cassettes jams
E3C, E3D, E3E, E3FLCF jams
F07Communication error between SYS board and LGC board
F10Hard drive initialization error
F11Communication error between SYS board and SLG board

Toshiba StudioE-550, 650, E-800 equivalent machines Lanier 5555 (Studio E-550), Lanier 5556 and Sharp AR651 (Studio E-650), Lanier 5580 and Sharp AR-810 (Studio E-800)
C04Paper feed motor
C11Duplex side guide
C12Duplex stopper guide problem
C131^st cassette  
C142^nd cassette 
C153^rd cassette   
C164^th cassette
C17PFP lower cassette
C18LCF tray up problem
C1ATandem LCF end fence motor
C1CLCF tray up motor
C26Peak detect error, exposure lamp
C27, C28Scan home problem
C29Exposure lamp problem
C36Charge corona cleaning problem
C37Transfer belt cam motor
CD1Brush motor locked
CD2Toner auger motor locked
CD3Used toner motor
CD4Waste toner full
C41Fuser thermistor or low temperature
C43Fuser problem after warm-up or fuser thermistor
C44Fuser problem
C45Side fuser thermistor bad
C46Fuser pressure roller thermistor badC47Power voltage problem
C48High IGBT temperature
C49IH circuit
C4AFuser web
CD5Web motor path error
C55Communication error between copier and RADF
C56Communication problem between CPU and PFC
C57Communication problem between CPU and IPC
C58Communication problem between IPC and finisher
C59Communication problem between CPU and laser CPU
C72RADF registration sensor problem
C73EEPROM initialization problem in RADF
C74RADF exit reverse sensor problem
C82RADF sensor adjustment error 
C83RADF original sensor adjustment error
C84RADF small original reverse sensor adjustment error
C85RADF lift tray motor
C86RADF large original exit sensor adjustment problem
C94Main CPU problem
CA1Laser motor (Polygon motor) problem
CA2Laser H-SYNC problem
CA3Laser secondary scan rough adjust error
CA5Laser power adjust error
CA6Laser calibration error
CA9Laser image data transmit error from SYS board
CAALaser secondary fine adjust error
CABLaser secondary scan inter-page error
CACLaser primary scan dot adjust error
CABSecondary scan interpage compensation error
CB1Finisher feed motor
CB2Finisher exit motor
CB3Finisher lift motor
CB4Finisher alignment motor
CB5Staple motor
CB6Stapler shift motor problem
CB7Finisher height sensor
CB8Backup RAM problem 
CB9Saddle stitcher paper push plate motor
CBASaddle stitcher front stitcher motor
CBBSaddle stitcher rear stitcher motor
CBCSaddle stitcher alignment motor
CBDSaddle stitcher guide motor
CBESaddle stitcher folding motor
CBFSaddle stitcher paper positioning plate motorCCOFinisher sensor connector error
CC1Finisher micro switch
CC2Saddle stitcher to finisher communication problem
CC4Finisher swing motor
CC5Finisher horizontal registration motor
E11Duplex jam
E12Bypass jam
E131^st cassette jam 
E142^nd cassette jam 
E153^rd cassette jam 
E164^th cassette jam
E18Tandem feed jam
E19LCF jam
E20, E21Jams from 1^st cassette
E22, E24Jams from 2^nd cassette
E25Jams from LCF
E30 - E333^rd cassette jam
E34 - E384^th cassettes jams
CC6Finisher punch motor
CC7Finisher punch unit backup RAM data
CCCFinisher to inserter communication problem
CCDFinisher inserter EEPROM problem
CCEFinisher inserter fan
CDOLaser initialize time out error
CEOLaser comparator problem
CE1Laser beam sensor detect error
CE2Laser sensor busy error
CE3Laser primary scan adjustment error
CE4Laser abnormal window comparator
E01Jam before fuser
E02Fuser jam
E03Jam at turn on
E09Hard drive error
E3C, E3D, E3E, E3FTandem LCF jams
E41 – E47Cover open jam
E50 – E59, E5ADuplex jam
E71 – E77, E7B, E7F, E80 – E85Document feeder jam
EA1 – EA9, E9F, EAA – EB3Finisher jams
EC - EC9, ECA – ECCInserter jam
EB5, EB6Jam in transport area
F07Communication error SYS board and LGC board
F10Hard drive format error
F11Communication error between SYS board and SLG board